Aluminum Extrusions for Solar Energy

Home > Industries > Solar Energy
Aluminum extrusion line and run-out table at the Bor Alüminyum plant in Çerkezköy, Türkiye

Aluminum extrusions for solar mounting rails and frames

Bor USA extrudes aluminum profiles for solar mounting systems to your drawing: mounting rails, purlins, legs and bracing members for ground and rooftop racking, clamp sections and module frame profiles. We cast the billets ourselves in 6005, 6063, 6061 and 6082, extrude profiles up to 12 m long, and cut, drill and pack them so they arrive ready for site assembly.

Alloys we cast
6005, 6063, 6061, 6082plus 6060, 6463, 6013, 6951
Largest cross-section
340 × 40 mm, 180 × 180 mmon the 9-inch, 2,800-ton press
Extruded length
Up to 12 mabout 39 ft
Machining
Cut and drilled to drawingthreading and milling too

What a racking profile has to survive

Carry wind and snow loads

Racking is sized to the loads at the site. Solar Power World's design guide recommends 6005A for structural solar profiles and notes that 6063 costs less and suits rooftop mounts where deflection matters more than strength.

Stay straight over long rails

Long rails have to line up with clamps and module rows without being forced into place. 6005A is less quench sensitive than 6061, so it distorts less after extrusion, which helps on long, thin sections.

Arrive ready to bolt together

We drill and thread the holes for clamps and splices at the plant, so your installers do not have to drill on the roof or in the field.

Last outdoors for the life of the array

Aluminum does not rust. Where appearance or extra protection matters, we can anodize the profiles, which increases their resistance to corrosion and wear.

Matching the alloy to the racking part

Most solar mounting extrusions are 6xxx-series alloys. Below is how the alloys we cast usually line up with solar parts, although your structural engineer's calculation makes the final call.

Alloy guide for solar profiles
AlloyTypical use
6005Main structural rails, purlins and legs in ground-mount and utility racking (the Solar Power World guide names 6005A for this role).
6063Rooftop rails, module frames and light parts where deflection governs.
6061Higher-strength members and machined clamps or brackets.
6082Heavy structural sections; common in European specifications.

Sources: Designing solar structures with aluminum extrusion (Solar Power World); 6005A aluminium alloy (Wikipedia). We cast 6005, 6063, 6061 and 6082 as billet in our own casthouse, while the 6005A recommendation comes from the Solar Power World guide; see billet casting.

From racking drawing to bundled rails

Solar racking has no catalog range with us: we extrude every rail and purlin to your drawing, and if a die from our library already fits, we use it.

  1. Send the drawing

    We need the profile drawing (DWG, DXF or PDF), the alloy and temper, length, finish, hole pattern and annual quantity.

  2. Die check

    We check the profile against our press envelopes and use an existing die or make a new one.

  3. Extrusion and finishing

    We extrude the profiles, age them to temper and supply them in mill finish or anodized.

  4. Machining and packing

    We cut and drill them to length, then pack them in bundles, crates or pallets for container shipping.

Industrial aluminum profiles in our catalog →

Reading for solar racking designers

Have a racking or rail drawing?

Send the drawing, alloy, length, hole pattern, finish and annual quantity, and we will reply with a quote.

Request a quote

Frequently asked questions

Which aluminum alloy is best for solar racking?
Design guides often recommend 6005A for structural solar profiles because it is strong and distorts less after extrusion than 6061. 6063 costs less and is used for rooftop rails and module frames where deflection governs. We cast 6005, 6063, 6061 and 6082 billets.
Can you extrude solar rails to my own drawing?
Yes. We extrude solar profiles to your drawing, and if none of the more than 7,000 profile types our plant has already produced fits, we make a new die.
How long can solar mounting rails be?
Up to 12 m (about 39 ft) from the press. We cut them to the length you specify.
Can you drill holes for clamps and splices?
Yes. At the plant we cut, drill, countersink, thread and mill the profiles to your drawing.
Do solar profiles need anodizing?
Not always. Aluminum does not rust, and many mounting profiles go out in mill finish. Anodize where the design calls for a uniform look or extra protection.

References

Bor USA

Get a Quote

Tell us briefly what you need and we will get back to you with a quote.

Your details are only used to respond to this request. Privacy Notice